Z13 type expansion joint sleeveWhen the rated load of is less than the load to be transferred, two or more expansion sleeves can be used in series, and the total rated load is: Mtn=m.Mt where: Mtn---n total rated load of expansion sleeves; m--- Load factor.
Tolerance and surface roughness of the bonding surface.
1.与胀套结合的轴和孔,其公差带按GB1800-79《公差与配合总论标准公差与基本偏差》和GB1801《公差与配合尺寸至500mm孔、轴公差带与配合》的规定。
2. The tolerance zone of the shaft and hole combined with the expansion sleeve is in accordance with the provisions of GB1031-83 "Surface Roughness Parameters and Values".The recommended ten-point height Rz of microscopic unevenness is listed in Table B.
The basic dimensions and parameters of the Z13 expansion sleeve:
A Basic dimensions (mm) Dimensions | Rated load | Socket head cap screws | Pressure on joint surface between expansion sleeve and shaft pt N / mm2 |
Pressure on the joint surface between expansion sleeve and wheel load pt N / mm2 |
weight kg |
|||||||||
d | D | L1 | L2 | L3 | L4 | D1 | Torque Mt kN |
Axial force Ft kN. m |
d1 | n | MA N. m |
|||
20 22 24 25 28 30 32 35 |
47 47 50 50 55 55 60 60 |
48 48 48 48 48 48 48 48 |
42 42 42 42 42 42 42 42 |
29 29 29 29 29 29 29 29 |
26 26 26 26 26 26 26 26 |
53 53 56 56 61 61 66 66 |
0.54 0.6 0.65 0.68 0.76 0.82 1.31 1.44 |
54 54 54 54 54 54 82 82 |
M6 M6 M6 M6 M6 M6 M6 M6 |
7 7 7 7 7 7 11 11 |
14 14 14 14 14 14 14 14 |
276 253 230 222 198 186 261 240 |
117 118 110 111 100 101 139 140 |
0.51 0.53 0.55 0.65 0.62 0.80 0.70 0.81 |
38 40 |
65 65 |
48 48 |
42 42 |
29 29 |
26 26 |
71 71 |
1.56 1.64 |
82 82 |
M6 M6 |
11 11 |
14 14 |
220 209 |
129 129 |
0.77 1.33 |
42 45 |
75 75 |
59 59 |
51 51 |
34.4 34.4 |
30 30 |
81 81 |
2.13 2.28 |
101 101 |
M8 M8 |
6 6 |
41 41 |
213 199 |
119 119 |
1.24 1.44 |
48 50 55 60 |
80 80 85 90 |
59 59 59 59 |
51 51 51 51 |
34.4 34.4 34.4 34.4 |
30 30 30 30 |
86 86 91 96 |
2.43 2.53 4.18 4.56 |
101 101 152 152 |
M8 M8 M8 M8 |
6 6 9 9 |
41 41 41 41 |
186 179 244 224 |
112 112 158 149 |
1.41 1.35 1.45 1.55 |
65 70 |
95 110 |
59 66 |
51 56 |
34.4 45 |
30 40 |
102 117 |
4.94 6.5 |
152 186 |
M8 M10 |
9 7 |
41 83 |
206 176 |
141 112 |
1.67 2.61 |
75 80 |
115 120 |
66 66 |
56 56 |
45 45 |
40 40 |
122 127 |
7 7.4 |
186 186 |
M10 M10 |
7 7 |
83 83 |
165 153 |
107 102 |
2.75 2.89 |
85 90 |
125 130 |
66 66 |
56 56 |
45 45 |
40 40 |
132 137 |
9 9.6 |
213 213 |
M10 M10 |
8 8 |
83 83 |
165 157 |
112 109 |
3.04 3.18 |
95 100 |
135 145 |
66 77 |
56 65 |
45 52 |
40 46 |
142 153 |
12.6 13.3 |
267 270 |
M10 M12 |
10 7 |
83 145 |
185 153 |
130 105 |
3.33 4.62 |
110 120 |
155 165 |
77 77 |
65 65 |
52 52 |
46 46 |
163 173 |
14.7 18.4 |
270 309 |
M12 M12 |
7 8 |
145 145 |
140 147 |
90 107 |
5.00 5.37 |
130 140 150 |
180 190 200 |
77 87.5 87.5 |
66 73.5 73.5 |
52 58.5 58.5 |
46 51 51 |
188 199 209 |
25.1 40.15 47 |
388 586 639 |
M12 M14 M14 |
10 11 12 |
145 230 230 |
171 213 217 |
124 157 163 |
6.46 7.73 8.21 |
160 170 180 |
210 225 235 |
87.5 87.5 87.5 |
73.5 73.5 73.5 |
58.5 58.5 58.5 |
51 51 51 |
219 234 244 |
54.3 63 66 |
692 746 746 |
M14 M14 M14 |
13 14 14 |
230 230 230 |
220 226 212 |
167 171 162 |
8.64 10.14 10.66 |
Note: 1. The data listed in the table is the rated load of the expansion sleeve when the spacer is configured with "A", and the rated load is 62% of the listed load when the spacer is configured; 2. The mechanical performance grade of Z13 type expansion screws is 12.9. |